Xlaserlab X1 Pro Review (2026): A 120 V Fiber 3-in-1 for Thin Sheet, With Caveats
Research-based, not hands-on: we have not tested these machines. Some links may pay us a commission, which never changes the order or the verdict. See our editorial policy.

The short verdict
The Xlaserlab X1 Pro is the cheapest fiber laser 3-in-1 we have found and one of only two on our list that runs on a standard US 120 V outlet. For thin sheet up to about 3 mm it covers welding, cleaning and cutting for $3,399.99 until December 4, then $3,799.99. The trade-offs are a 1-year warranty, expensive consumables and a product page that contradicts itself on the wire feeder, the weight and the thickness it welds.
We have not used an X1 Pro. This review is built from Xlaserlab's product page, read on October 30, 2026 with the prices read again on November 5, and the sources named below. Our editorial policy explains the method, and the affiliate disclosure says which links may pay us.
Price and kits
| Kit | Black Friday price | After December 4 | Shown against |
|---|---|---|---|
| Standard Kit | $3,399.99 | $3,799.99 | $3,999.99 |
| Professional Kit | $4,099.99 | $4,299.99 | $4,999.99 |
Each kit comes with a US, EU, UK or Australian plug. An Ultimate Kit at $3,799.99 was listed on October 18 and was gone by October 30. The page did not itemize what the Professional Kit adds; its FAQ lists a "wire feeder (Single/Dual)", so ask which feeder each kit includes before you pay $700 more.
The later prices are Xlaserlab's own figures, and the Standard Kit's is $200 above its October price. The $100 checkout discount the page showed on October 30 was gone on November 5. Xlaserlab's affiliate team has given our readers the code AFF5 for 5% off sitewide and says it stacks with the sale prices, which would make the Standard Kit $3,229.99 until December 4. We have not tried it at checkout.
What Xlaserlab claims it does
- Welding. 0.5 to 3 mm in one pass in stainless and carbon steel, per the spec table and the FAQ. Aluminum "up to approximately 0.5–2mm at 100% power".
- Cutting. Stainless and carbon steel up to 3 mm.
- Cleaning and surface prep. Burning off oxides, paint and coatings at the weld zone.
Elsewhere the same page says "From 0.008" (0.2mm) thin sheet to 0.2" (5mm) structural stock". We go by the 0.5 to 3 mm figure, which is in the spec table and repeated in the FAQ.
Specifications
| X1 Pro | |
|---|---|
| Laser | 700 W fiber, 1080 ± 10 nm |
| Cooling | Air |
| Input | 100 to 250 V AC, 50/60 Hz |
| Weight | 21 kg in the spec table, 19 kg in the FAQ |
| Size | 470 x 205 x 335 mm |
| Controls | 7-inch touchscreen with presets; the gun stores 3 custom presets |
| Warranty | 1 year, plus replacement of core hardware that fails within 60 days of delivery |
What is in the box, and what is not
The FAQ lists the main unit, welding gun, a wire feeder, gun holder, cables, gas hose and adapter, 2 focusing lenses, 5 protective lenses, an external emergency stop, a laser welding helmet (OD 8 from 950 to 1100 nm, per the FAQ), safety goggles, an apron and a nozzle box for 0.8 to 1.6 mm wire. Xlaserlab says you supply shielding gas (argon or nitrogen) and filler wire yourself.
If your kit turns out to lack the feeder you want, Xlaserlab sells a single wire feeder for $199.99 and a dual wire feeder for $899.99.
Consumables are where the low entry price narrows. Xlaserlab's 5 kg spools are ER70S-6 at $79.99 and ER308L at $179.99, against $32.99 and $115.99 for xTool's. Our cost guide puts a first year with the Standard Kit, gas, wire, glasses and a fume extractor at about $4,594, or about $4,994 after December 4.
What we like
- 120 V. It runs on a standard US household outlet as well as a 240 V circuit, so there is no electrician's bill to start.
- Price. The lowest entry price for a fiber welder that also cleans and cuts.
- Size. At 21 kg it can go in a car and onto a job site.
- Eye protection included. A helmet and goggles in the box, with the helmet's band stated.
- A shipping promise. One free accessory worth $69.99 to $99.99 if your order has not shipped within 5 working days or arrived within 20.
What gives us pause
- "FDA & CE MD Approved". The FDA does not approve laser products; makers report them and receive an accession number. We found no number for the X1 Pro, so ask for it. Our safety guide explains what to look for.
- The wire feeder. One part of the page calls the dual wire feeder included, a heading a few lines later marks it "(Optional)", and the FAQ says "Single/Dual".
- Weight. 21 kg in the specs, 19 kg in the FAQ.
- Warranty. One year is the shortest cover on our list, shared with OMTech and xTool's standard warranty. ARCCAPTAIN gives three years on both its machines.
- Returns. 30 days, unused only, with an 8% to 15% fee on non-defective returns. A machine that has welded cannot go back for a change of mind.
- Shipping time to the US. The page gives 3 to 5 business days for Canada, the UK and most EU countries, and says other regions "may vary".
Who it suits
A home garage or small shop without 240 V, welding sheet metal up to about 3 mm: brackets, exhaust, panels, light fabrication. If you weld thicker steel or want more documentation and support, look at the xTool MetalFab in our MetalFab vs X1 Pro comparison. The lighter ARCLUME AIR 500 is also on 110 to 240 V, with a 3-year warranty, but it is a pre-order. The full field is in our best handheld laser welder guide.
What we could not verify
- Weld quality on any machine we have not used, including this one.
- An FDA accession number for the X1 Pro.
- Which wire feeder comes with which kit.
- Current draw on a 120 V circuit at full power.
Machines in this guide
Figures are from each maker's own page. Links go to the maker and may be affiliate links; see our disclosure.

Welder + cleaner + cutter
Xlaserlab X1 Pro
$3,399.99
Standard Kit, Black Friday price, then $3,799.99 after December 4; Professional Kit $4,099.99, then $4,299.99
Code AFF5: 5% off sitewide, on top of sale prices at Xlaserlab
- Laser
- 700W fiber
- Cooling
- Air
- Maker claim
- Welds 0.5 to 3 mm; cuts up to 3 mm
- Warranty
- 1 year, plus 60-day replacement for major hardware failures
- Weight
- 21 kg (its own FAQ says 19 kg)
- Power input
- 100 to 250 V, runs on a US 120 V outlet
The cheapest fiber 3-in-1 here, and it runs on a standard US 120 V outlet. The lowest entry price also means the shortest warranty.
What we could not verify
- The maker says it is "FDA & CE MD Approved". The FDA does not approve these products and we found no accession number.
- The page says a dual wire feeder is included and, a few lines later, that it is optional. Ask which kit includes it.
- Thickness claims range from 0.5 to 3 mm in the specs to "0.2mm to 5mm" in the marketing copy.
Price read from the maker's page on November 5, 2026. It will have changed by the time you click.
Keep reading

xTool MetalFab vs Xlaserlab X1 Pro (2026): Which 3-in-1 Laser Welder to Buy
The two cheapest fiber laser 3-in-1s side by side: $3,999 against $3,399.99 at Black Friday prices, 240 V against 120 V, 4 mm against 3 mm. Price, specs, what is in the box, running costs and which buyer each one suits.

Best Handheld Laser Welders (2026): Eight Portable Models Compared, and What They Actually Weld
Eight handheld laser welders from $2,999.99 to $8,499, compared on price, weight, power input and warranty, with the thickness each maker claims and ten things to check before you pay. Which ones are truly portable, which run on 120 V, and what each maker leaves unsaid.

Laser Welder Price (2026): What a Handheld Laser Welding Machine Costs, and What You Pay On Top
How much is a laser welder? Handheld units list at $2,999.99 to $8,499, and $12,499 for a 2000 W model. Prices per watt, plus the gas, wire, eyewear and extraction that sit on top.

Laser Welder and Rust Remover Safety: Class 4 Rules, Eyewear, Fumes and Imports
Handheld laser welders and cleaners are Class 4 lasers. What the rules say, how to match eyewear to the wavelength, what the fumes hold and why an FDA claim is not an FDA number.