Handheld Laser Guide
All guides

Laser Welder Price (2026): What a Handheld Laser Welding Machine Costs, and What You Pay On Top

By Stefan FlorinUpdated 7 min read

Research-based, not hands-on: we have not tested these machines. Some links may pay us a commission, which never changes the order or the verdict. See our editorial policy.

A handheld laser welder next to an argon cylinder, wire spools and safety glasses

How much is a laser welder?

A handheld laser welder lists at $2,999.99 to $8,499 for the models we priced, and $12,499 for the Everlast RedSabre 2000. The cheapest is a 460 W diode unit for thin sheet. A fiber welder that takes filler wire starts at $3,399.99, a Black Friday price that ends December 4. A first year of gas, wire, eyewear and fume extraction adds roughly $950 to $1,200 to that, from the listed prices below.

This page covers handheld welders sold direct to small shops and home garages. Machine prices were read from each maker's own page on October 18, 2026, and xTool, Xlaserlab, ARCCAPTAIN and the OMTech 1500W again on October 30, with the xTool, X1 Pro and ARCCAPTAIN prices read once more on November 5, unless we say otherwise. We have not bought or tested any of them.

Laser welding machine prices

MachineLaserListed pricePrice per wattWarranty
Xlaserlab X1460 W diode$2,999.99$6.521 year
Xlaserlab X1 Pro700 W fiber$3,399.99 (then $3,799.99 after December 4)$4.861 year
OMTech 1000W1000 W fiber$3,599.99 (sold out)$3.601 year
ARCLUME AIR 500 3-in-1 Handheld Laser Welder500 W fiber$3,999.99 (pre-order)$8.003 years
xTool MetalFab 800W800 W fiber$4,499 ($3,999 at checkout until December 4)$5.6212 months
OMTech 1500W 3-in-11500 W fiber$5,299.99 (pre-order)$3.531 year
xTool MetalFab 1200W1200 W fiber$6,699 ($5,999 at checkout until December 4)$5.5812 months
ARCCAPTAIN LW1200 1200W Handheld Laser Welder1200 W fiber$6,899 (sale)$5.753 years
Everlast RedSabre 15001500 W fiber$8,499$5.675 years
Everlast RedSabre 20002000 W fiber$12,499 (read October 4)$6.255 years

Price per watt is a rough guide, not a quality score. OMTech is cheapest per watt by a wide margin, but its 1000W was sold out and its 1500W is a pre-order. The AIR 500 is the most expensive per watt because it is the smallest laser here, not because it is the dearest machine. The X1 is a diode laser, so its watts are not directly comparable with the fiber units. And watts say nothing about warranty: Everlast costs more per watt than OMTech and gives five years instead of one.

What decides the price

  • Laser power. 500 to 1000 W fiber units list at $3,399.99 to $4,499. At 1200 to 1500 W the range runs from $5,299.99 to $8,499.
  • Diode or fiber. The only diode unit, the X1, is the cheapest, but it lists 0.2 to 2 mm and does not mention filler wire.
  • What is in the box. OMTech includes a wire feeder and glasses with the 1000W. xTool lists goggles as included. The X1 Pro page calls its dual wire feeder both included and optional. If your kit turns out to lack one, Xlaserlab sells a single wire feeder for $199.99 and a dual wire feeder for $899.99.
  • Warranty and seller. One year from most importers, three years from ARCCAPTAIN on both its machines, five from Everlast.

The price you actually pay

Several listings show a much higher "regular" price: OMTech 1000W against $7,499.99, OMTech 1500W against $10,599.99, ARCCAPTAIN against $10,999, the AIR 500 against $5,199.99, the MetalFab 800W against $4,699 and the X1 Pro against $3,999.99. That is the seller's framing. Judge each machine by what you would pay.

Black Friday moves these numbers until December 4. xTool's page takes $500 off the MetalFab 800W and $700 off the 1200W at checkout. Xlaserlab has cut the X1 Pro to $3,399.99 and says it returns to $3,799.99 afterwards. ARCCAPTAIN has cut the LW1200 from $7,299 to $6,899 without giving an end date, and offers $500 off the AIR 500 during its presale. Xlaserlab's affiliate team has also given readers the code AFF5 for 5% off sitewide and says it stacks with the sale prices, which would bring the X1 Pro Standard Kit to $3,229.99. We have not tried it at checkout.

Extras you need, with prices

ItemPriceSource
Argon, 80 cu ft, contents only (refill, no cylinder)$69.99Tractor Supply, read October 4
ER70S-6 steel wire, 1.0 mm, 5 kg$79.99Xlaserlab
ER70S-6 steel wire, 0.04 in, 11 lb (5 kg)$32.99xTool
ER308L stainless wire, 1.0 mm, 5 kg$179.99Xlaserlab
ER308L stainless wire, 0.04 in, 11 lb (5 kg)$115.99xTool
Laser safety glasses, 1064 nm$194.00Laser Safety Industries, read October 4
Laser safety glasses, OD 5+ from 835 to 1095 nm$155 to $200Phillips Safety
Fume extractor that mentions welding (OMTech 300W, 467 m³/h)$749.99OMTech
Fume purifier made for engravers (Cloudray 250W, 380 m³/h)$489Cloudray
xTool MetalFab protection lenses, 10-pack$99xTool

Wire is the line where the seller matters most: xTool lists the same 5 kg spools for $32.99 and $115.99, against $79.99 and $179.99 at Xlaserlab. We have not checked whether one maker's spool fits the other's feeder, so ask before you mix.

A note on the glasses: fiber welders run near 1080 nm. xTool states its welder needs eyewear for 1080 plus or minus 10 nm at an optical density above 6. Glasses rated only at 1064 nm, or rated OD 5 at 1080 nm, may not meet that. Do not buy by price. Match the band and the density the maker asks for. See the safety guide.

A first-year sketch from sourced prices only

Xlaserlab X1 ProxTool MetalFab 800W
Machine$3,399.99$3,999
One argon refill$69.99$69.99
5 kg ER308L wire (each maker's own)$179.99$115.99
Laser safety glasses$194.00Listed as included
Fume extractor (OMTech 300W)$749.99$749.99
Total$4,593.96$4,934.97

Those are the Black Friday machine prices. At the prices that follow on December 5, $3,799.99 and $4,499, the totals are $4,993.96 and $5,434.97. They leave out an argon cylinder if you do not own one, sales tax, shipping, electrical work and training. They are a floor, not a quote.

Running costs the makers mention

xTool says its nozzle set lasts about 3 months and a pack of 10 protection lenses about 2 months. At $99 for a 10-pack, that would be about $600 a year in lenses on xTool's own figures. Those are maker estimates with no stated usage, so treat them as a guide. We found no independent data on gas or wire use per hour.

Power and installation

Only the X1 Pro and the AIR 500 list a standard US 120 V outlet. The X1 is 220 V only, the MetalFab wants 200 to 240 V, OMTech and ARCCAPTAIN list 220 V and the Everlast 240 V single phase. If your garage or shop has no 240 V circuit, an electrician's quote belongs in the budget. We did not price electrical work, and xTool's own pages have given different circuit ratings for the 1200W.

Hidden costs: returns and duties

Return terms differ a lot. xTool charges 10% (unopened), 15% (opened, unused) or 30% (opened, used) of the order total, and says the machine must have been "lasered less than 50 times". Xlaserlab lists a tiered fee of 8% to 15% for non-defective returns. On a $4,499 machine, a 30% fee is about $1,350. ARCCAPTAIN ships from a US warehouse. We could not confirm tariff treatment for any of these machines from an official source, so ask the seller who pays.

Is it worth the price?

That depends on what you weld and what you use now. We compare the two methods in laser welding vs TIG, and the best handheld laser welder guide picks a model for each kind of buyer.

What we could not verify

  • Current tariff rates on these machines.
  • The cost of training and electrical work.
  • Whether the AFF5 code really stacks with the sale price at checkout; we have only Xlaserlab's word.
  • Whether the pre-order prices hold after the presales end.

Machines in this guide

Figures are from each maker's own page. Links go to the maker and may be affiliate links; see our disclosure.

Xlaserlab X1 diode welder

Welder

Xlaserlab X1 diode welder

$2,999.99

Ultimate Pack, shown as reduced from $3,699

Code AFF5: 5% off sitewide, on top of sale prices at Xlaserlab

Laser
460W diode, 976 nm
Cooling
Air
Maker claim
Stainless and carbon steel 0.2 to 2 mm; pulsed and spot welding
Warranty
1 year
Weight
13 kg (another Xlaserlab page says 12 kg)
Power input
220 V only

The cheapest laser welder we found, made for thin sheet. It is a diode, not a fiber laser, the page never mentions filler wire, and it will not run on a 110 to 120 V outlet.

What we could not verify
  • The page says it runs only on 220 V and suggests a step-up transformer, which Xlaserlab does not sell.
  • Aluminum is missing from its own materials list, although the X1 Pro page lists aluminum for the X1.
  • The page shows an add-to-cart button and an "Email me when available" form at the same time.

Price read from the maker's page on October 18, 2026. It will have changed by the time you click.

Xlaserlab X1 Pro

Welder + cleaner + cutter

Xlaserlab X1 Pro

$3,399.99

Standard Kit, Black Friday price, then $3,799.99 after December 4; Professional Kit $4,099.99, then $4,299.99

Code AFF5: 5% off sitewide, on top of sale prices at Xlaserlab

Laser
700W fiber
Cooling
Air
Maker claim
Welds 0.5 to 3 mm; cuts up to 3 mm
Warranty
1 year, plus 60-day replacement for major hardware failures
Weight
21 kg (its own FAQ says 19 kg)
Power input
100 to 250 V, runs on a US 120 V outlet

The cheapest fiber 3-in-1 here, and it runs on a standard US 120 V outlet. The lowest entry price also means the shortest warranty.

What we could not verify
  • The maker says it is "FDA & CE MD Approved". The FDA does not approve these products and we found no accession number.
  • The page says a dual wire feeder is included and, a few lines later, that it is optional. Ask which kit includes it.
  • Thickness claims range from 0.5 to 3 mm in the specs to "0.2mm to 5mm" in the marketing copy.

Price read from the maker's page on November 5, 2026. It will have changed by the time you click.

xTool MetalFab 800W

Welder + cleaner + cutter

xTool MetalFab 800W

$4,499

800W, shown as reduced from $4,699, with $500 off at checkout until December 4 ($3,999); the 1200W is $6,699, with $700 off ($5,999)

Laser
800W fiber (1200W also sold)
Cooling
Air
Maker claim
Welds up to 4 mm (800W) or 5 mm (1200W)
Warranty
12 months, longer plans sold separately
Weight
35 kg (800W), 38.2 kg (1200W)
Power input
200 to 240 V

The best-documented option, with a cited third-party test of the weld and goggles listed as included. The electrical specs differ between xTool's own pages, so check them before you wire a circuit.

What we could not verify
  • xTool's pages give three different circuit requirements for the 1200W.
  • Plug type is not stated.

Price read from the maker's page on November 5, 2026. It will have changed by the time you click.

Welder + cleaner + cutter

OMTech 1500W 3-in-1

$5,299.99

Shown as reduced from $10,599.99

Laser
1500W fiber
Cooling
Water (built-in chiller, per the listing)
Maker claim
Stainless and carbon steel 4 mm, aluminum 2 mm
Warranty
1 year
Power input
220 V

Welds, cleans and cuts, with an automatic wire feeder and 20 nozzles. Laser safety glasses are not included.

What we could not verify
  • Sold as a pre-order shipping December 30, while the same page says orders ship in 1 business day.
  • Weight and laser class are not stated.
  • Shielding gas (argon or nitrogen) is not included.

Price read from the maker's page on October 30, 2026. It will have changed by the time you click.

Welder

Everlast RedSabre 1500

$8,499

Shown as reduced from $9,999.99

Laser
1500W fiber
Cooling
Air
Maker claim
Stainless and mild steel 4 mm, aluminum 3.5 mm
Warranty
5 years
Weight
181 lb (82 kg)
Power input
240 V single phase

Priced well above the imports, with a 5-year warranty from a US seller. The one to look at if support matters more than the sticker price.

What we could not verify
  • Everlast's page says 181 lb for the 1500 and 135 lb for the more powerful 2000. One of those is probably wrong.

Price read from the maker's page on October 18, 2026. It will have changed by the time you click.

Keep reading